- Waterproof (IP67 certified*)
- 2” color display with resistive touchscreen
- Compatible with 5 different models of O2 sensors: BOSCH 4.2 / 4.9 / 5.2 / NTK ZFAS-U2 (laboratory) and NTK ZFAS-A2 (PN: UAR0004)
-
Different fuels AFR or lambda display unit options **
- Lambda (0.21 - 9.99)
- AFR Methanol (1.35 - 64.6)
- AFR Gasoline (3.09 - 146.6)
- AFR Ethanol (1.89 – 89.9)
-
CAN communication with Power FT ECU’s:
- “Second display gauge” function that allows display valuable information like Oil Pressure, Fuel Pressure, Boost, RPM, Engine Temperature and much more coming from the FTCAN 2.0, with the possibility of configuring up to 5 custom screens
- “Switch Panel” function, touchscreen buttons or switches via CAN bus to the PowerFT ECU.
- 3 configurable O2 sensor heating modes: Normal, Fast and Current Limited, as well activated by engine RPM or temperature
- Advanced heater diagnostics in the PowerFT ECU datalogger
- 0-5V analog output for connection with any data acquisition or programmable injection system.
- Maximum power supply voltage: 20V
- Automotive connector
*with product harness connected
** The reading range can reach values slightly lower or higher than 0.21 λ, depending on the manufacturing characteristics of the sensor.
Dimensions
- Dimensions: 2.64” x 1.83” x 1.48” (in)
Weight
- Module: 1.84 oz
- Product: 3.99 oz
Contents of packaging
- NanoPRO module
- Instructions guide
- 4 screws for fixation
Warranty
Limited Warranty. The warranty on this product is 1 year from the date of purchase and covers manufacturing defects only
Harness & sensor options not included, see options below.
The evolution in O2-sensor conditioners. With a new design, the FuelTech NanoPRO is able to condition and read 5 different models of wide band lambda O2 sensors:
- Waterproof (IP67 certified*)
- 2” color display with resistive touchscreen
- Compatible with 5 different models of O2 sensors: BOSCH 4.2 / 4.9 / 5.2 / NTK ZFAS-U2 (laboratory) and NTK ZFAS-A2 (PN: UAR0004)
-
Different fuels AFR or lambda display unit options **
- Lambda (0.21 - 9.99)
- AFR Methanol (1.35 - 64.6)
- AFR Gasoline (3.09 - 146.6)
- AFR Ethanol (1.89 – 89.9)
-
CAN communication with Power FT ECU’s:
- “Second display gauge” function that allows display valuable information like Oil Pressure, Fuel Pressure, Boost, RPM, Engine Temperature and much more coming from the FTCAN 2.0, with the possibility of configuring up to 5 custom screens
- “Switch Panel” function, touchscreen buttons or switches via CAN bus to the PowerFT ECU.
- 3 configurable O2 sensor heating modes: Normal, Fast and Current Limited, as well activated by engine RPM or temperature
- Advanced heater diagnostics in the PowerFT ECU datalogger
- 0-5V analog output for connection with any data acquisition or programmable injection system.
- Maximum power supply voltage: 20V
- Automotive connector
*with product harness connected
** The reading range can reach values slightly lower or higher than 0.21 λ, depending on the manufacturing characteristics of the sensor.
Dimensions
- Dimensions: 2.64” x 1.83” x 1.48” (in)
Weight
- Module: 1.84 oz
- Product: 3.99 oz
Contents of packaging
- NanoPRO module
- Instructions guide
- 4 screws for fixation
Warranty
Limited Warranty. The warranty on this product is 1 year from the date of purchase and covers manufacturing defects only
REQUIRES
The NanoPRO has a 12-way connector with 3 wire groups. One of them has the connector for the O2 sensor, the second makes the CAN communication with Power FT ECU’s and the third is responsible for power and analog output.
The FuelTech NanoPRO has the same connector as the already established WB-O2 NANO, so if the vehicle already has a NANO installed, just disconnect it and install the new NanoPRO in the place that the probe signal reading will already be working.